Users

All Posts (6)

avatar

rvecchi

2FA on multiple clients

avatar
avatar
avatar
avatar

Good morning and thanks for the feedback.

Basically, if I understand correctly.

- TOTP at the Desktop application level is managed via the application itself. Copying the "RemoteDesktopManager.cfg" file should cause the devices to which the file is copied to inherit the TOTP configuration (thereby requiring only one instance).

- If the Web platform is used, with the indicated settings, the request for the second would be forced

authentication factor upon the occurrence of each event (Browser Refresh or opening of a new window). In any case, this setting would not impact the Desktop application (unless the username and password request window is presented, in which case the TOTP request procedure would be triggered).

I hope I understood the mechanism correctly.

Thanks again

2FA on multiple clients

avatar
avatar
avatar
avatar

Good morning,

I have been using the Free version of RDM for some time now (updated to version 2024.1.14.0 64-bit).

As a database, I use Devolution Hub Personal.

Of course, for security reasons, I have enabled TOTP via Google Authenticator, which works without any problems. The only "difficulty" lies in accessing the same database from different systems.

If I have configured TOTP on one system, is it possible to use the same Secret Key on other systems or will each of these have to have a different authentication instance?

I ask this because I usually use three different Windows systems to access the same Data Source and it would be extremely convenient to be able to have a single MDA instance of Google Authenticator, rather than having to create three.

Could copying the RemoteDesktopManager.cfg file (which I haven't tested yet) allow me to obtain the desired result?

In the meantime, I thank you for your support and send you my best regards.

Roberto

2FA With Google Authenticator

avatar
avatar
avatar
avatar

Good morning,

I finally found the solution to the problem. After trying everything, including what you suggested which is copying the config file instead of importing.

In practice, although the clocks of the two PCs in question were perfectly synchronized ("Set time automatically" activated and time synchronization also performed manually on both PCs), on the second system activating the "Set time zone automatically" option resolved the the problem. The clocks were still synchronized, but only by activating the above option (obviously active in the source system but not active in the destination system) is it now possible to use a single instance of Google Authenticator for both PCs.

Thanks a lot for your support.

Sincerely.

Roberto

2FA With Google Authenticator

avatar
avatar
avatar
avatar

Good morning,

thanks for replying.

Yes, the scenario is the first described. I generated a file called remotedesktopmanager.cfg by exporting the configuration with the "Include data source credentials" checkbox enabled. That same file was imported on the second Computer, but the Google Authenticator instance running on Computer A (from which it is the configuration was exported) does not work on Computer B (where it was imported).

As for date and time, they are exactly the same on both systems.

Thanks again.

Sincerely.

2FA With Google Authenticator

avatar
avatar
avatar
avatar

Good morning,

I apologize for the delay in replying.

In relation to what has been indicated, I would have some fear of importing from Computer B to Computer A as the latter is a critical system and I would not like the configuration to be altered in some way, making it unusable.

As for the "Independent" configuration of 2FA on Computer B, I confirm that it works correctly (but in this case, I should have two instances on Google Authenticator that actually refer to the same Data Source).

Thanks again for the support.

2FA With Google Authenticator

avatar
avatar
avatar
avatar

Good morning everyone,

I'm experiencing an anomaly related to being able to use the same instance of Google Authenticator on multiple devices.

Until recently, I was using the same 2FA code to access Remote Desktop Manager Free from two different PCs. What I did was export the configuration from Computer A and then import it into Computer B, also flagging the "Include data source credentials" option during export. This way it has always worked.

A few weeks ago I had to restore the operating system on Computer B and therefore I did the same operation. However, in this case, after having imported the configuration previously exported from Computer A, the system requests the TOTP code but signals "Invalid Code". Am I doing something wrong, or has something changed procedurally?

On both systems I'm using the 2022.3.23.0 64-bit version of Remote Desktop Manager Free.

Thanks so much for the support.

Sincerely.

Robert

1 - 6 of 6 items